77范文网 - 专业文章范例文档资料分享平台

GMW14651_06MR07_Material Related Interior Plastic Part Perfo

来源:网络收集 时间:2021-04-05 下载这篇文档 手机版
说明:文章内容仅供预览,部分内容可能不全,需要完整文档或者需要复制内容,请下载word后使用。下载word有问题请添加微信号:或QQ: 处理(尽可能给您提供完整文档),感谢您的支持与谅解。点击这里给我发消息

Material Related Interior Plastic Part Performance

Monolithic Plastic Parts and Injection Molded Plastic Substrates

Table 1: Installation Position1

Position within vehicle is exposed to directsunlight (exposed positions), such ashorizontal surfaces above glass line.These parts are exposed to temperaturesup to +105 °C in the vehicle. Including thefollowing typical parts but not limited to:package shelf, IP upper horizontal, rearseat back upper to rear window trimpanel, rear seat head restraint/roll over(vehicle only), load floor hatch back area(if designed without load compartment lid).Position within vehicle is exposed to directsunlight, this means below glass line.These parts are exposed to temperaturesup to +95 °C in the vehicle. Including thefollowing typical parts but not limited to:side trim below belt line, steering wheelrim, garnish moldings - upper, horizontalportion (A and C pillar for vehicle, D pillarfor truck, hatch back vehicle quarter trim),seat cushion, back, remining headrestraints, belt guide loops, seat shoulderand armrests), horizontal surface of thecenter console (vehicle only), open rearcargo area vertical glass (truck only) at orjust below the glass line.

Position within vehicle is not exposed todirect sunlight. These parts are exposedto temperatures up to +85 °C in thevehicle. Including the following typicalparts but not limited to: floor carpet,overhead consoles, IP vertical surfacesbelow door glass line, steering wheel face,steering column and shroud, garnishupper without horizontal features and allother garnish ,seat upper, truck 2nd and3rd row seats (no open or transparentoofconfiguration and not in the back window),door trim panel complete, center consolehorizontal truck geometry, center consolesides, overhead parts, open rear cargoarea verticle glass (truck only) floor level,floor level parts.

Page 1 of 6

1 Introduction

In addition to the requirements in GMW14651 allinterior parts as assembled parts must meet theapplicable requirements of GMW14444.

Note:Nothing in the specification supersedesapplicable laws and regulations.

Note:In the event of conflict between the Englishand domestic language, the English languageshall take precedence.

1.1 Scope. This specification defines the generalperformance requirements for plastic componentsand parts used for interior applications onautomobiles. These are integrally coloredmonolithic plastic components and parts as wellas plastic substrate materials for non-visiblecomponents and parts.

Note:Additional requirements for coated orpainted plastic parts are given in the relevant paintperformance specifications.

Note: Some sections reference both, GMW testmethod and local test methods, as soon the GMWis available, it supersedes the local test methods.1.2 Mission/Theme.Not applicable.1.3 Classification.

The requirements are classified by:

1.3.1 Installation Position (see Table 1).Aselected material shall support the partperformance for all environmental conditionsdefined by the installation position of the part inthe vehicle.

Note: The temperatures in Table 1 are measuredunder solar glass (tinted glass). If non-solar glassis used, up to +15 °C higher temperatures willoccur and the requirements shall be adjustedaccordingly.

2

3

© Copyright 2007 General Motors Corporation All Rights Reserved

March 2007

Originating Department: GME Specification Center

百度搜索“77cn”或“免费范文网”即可找到本站免费阅读全部范文。收藏本站方便下次阅读,免费范文网,提供经典小说教育文库GMW14651_06MR07_Material Related Interior Plastic Part Perfo在线全文阅读。

GMW14651_06MR07_Material Related Interior Plastic Part Perfo.doc 将本文的Word文档下载到电脑,方便复制、编辑、收藏和打印 下载失败或者文档不完整,请联系客服人员解决!
本文链接:https://www.77cn.com.cn/wenku/jiaoyu/1210813.html(转载请注明文章来源)
Copyright © 2008-2022 免费范文网 版权所有
声明 :本网站尊重并保护知识产权,根据《信息网络传播权保护条例》,如果我们转载的作品侵犯了您的权利,请在一个月内通知我们,我们会及时删除。
客服QQ: 邮箱:tiandhx2@hotmail.com
苏ICP备16052595号-18
× 注册会员免费下载(下载后可以自由复制和排版)
注册会员下载
全站内容免费自由复制
注册会员下载
全站内容免费自由复制
注:下载文档有可能“只有目录或者内容不全”等情况,请下载之前注意辨别,如果您已付费且无法下载或内容有问题,请联系我们协助你处理。
微信: QQ: