77范文网 - 专业文章范例文档资料分享平台

thermal_considerations_for_high_brightness_LEDs_5

来源:网络收集 时间:2021-04-05 下载这篇文档 手机版
说明:文章内容仅供预览,部分内容可能不全,需要完整文档或者需要复制内容,请下载word后使用。下载word有问题请添加微信号:或QQ: 处理(尽可能给您提供完整文档),感谢您的支持与谅解。点击这里给我发消息

© 2006 Zetex Semiconductors plc Feature article

Reference: ZE0500

Date: 5 October 2006

Thermal considerations for high brightness LEDs Colin Davies, Applications Manager, Zetex Semiconductors

Much attention is being focused on the dimming strategies used for controlling high brightness LEDs in a rapidly increasing number of applications. The nature of these devices demands however that even more attention be paid to thermal control.

While LED manufacturers are pushing back the technological boundaries by dramatically increasing the Lumens per Watt, there is still more electrical power converted to conducted heat than to light output. An overall strategy of thermal management is required to ensure that the power into the LED is controlled as a function of temperature.

The curve in figure 1 shows typical derating characteristics for a 1W LED. As expected, this clearly shows that the LED is driven with constant current up to a point at which the current then needs to be reduced linearly to 0 at 150°C. The point at which this derating occurs and the slope of the decrease is dependent on the mechanical/thermal heat sinking arrangement.

Fig 1

2

The control electronics must therefore be able to cope with a trip point setting and a gain setting. It’s also important to remember that the LED needs to be able to cope in fact with three potential contributors to the heating effect: self heating, ambient temperature and the LED electronic control. If the electronic control is remote from the LED illumination, then this will not be an issue – EMC however may be a concern.

Linear control of the LED

Take a trip back to the textbook and the first and most obvious way of controlling an LED is with a resistor. Although a low cost method, it inevitably results in power loss which negates or diminishes the LED’s key efficiency attribute. Using a variable resistor as the dimming element is also impractical for high brightness LEDs since the power in the resistor will be too large and a dedicated wire wound device would be required. As an illustration, for a single 1W LED taking 350mA from a 12V supply, around 2.5W would be wasted in the dimming resistor at full brightness. And if the resistor is in close proximity to the LED then the extra heating it produces will only add to the problem.

The pass element could of course be a transistor, which would mean the power dissipation resides in the transistor and not the variable resistor. This approach provides more flexibility by enabling logarithmic response, negative (NTC) or positive (PTC) temperature coefficient thermistors to be used for thermal control and brightness definition. A bit of imagination then easily leads to the use of optical feedback for automatic brightness control.

The transistor could be of any type: MOSFET, NPN bipolar or PNP bipolar. Amazingly some engineers of a more digital persuasion still believe that MOSFETs are better for this application because of their low on resistance! It simply has to be understood that linear power dissipation is the same regardless of silicon choice. It’s still wasted power in the form of heat which needs to be managed.

© 2006 Zetex Semiconductors plc

百度搜索“77cn”或“免费范文网”即可找到本站免费阅读全部范文。收藏本站方便下次阅读,免费范文网,提供经典小说教育文库thermal_considerations_for_high_brightness_LEDs_5在线全文阅读。

thermal_considerations_for_high_brightness_LEDs_5.doc 将本文的Word文档下载到电脑,方便复制、编辑、收藏和打印 下载失败或者文档不完整,请联系客服人员解决!
本文链接:https://www.77cn.com.cn/wenku/jiaoyu/1208306.html(转载请注明文章来源)
Copyright © 2008-2022 免费范文网 版权所有
声明 :本网站尊重并保护知识产权,根据《信息网络传播权保护条例》,如果我们转载的作品侵犯了您的权利,请在一个月内通知我们,我们会及时删除。
客服QQ: 邮箱:tiandhx2@hotmail.com
苏ICP备16052595号-18
× 注册会员免费下载(下载后可以自由复制和排版)
注册会员下载
全站内容免费自由复制
注册会员下载
全站内容免费自由复制
注:下载文档有可能“只有目录或者内容不全”等情况,请下载之前注意辨别,如果您已付费且无法下载或内容有问题,请联系我们协助你处理。
微信: QQ: