中海油员工英语手册(3)

catenary anchor leg mooring 悬链锚腿系泊 (CALM)

cathodic protection cellar deck cement grout cementing vessel center line center of buoyancy center of floatation center of gravity center punch

central control room (CCR) central processing platform centrifugal pump Centrifuger ceramic fibres ceramic tiles certifying authority chain block chair with arm-rests Chamfering channel steel

charpy-V notch energy

11

阴极保护 底甲板 水泥浆 固井船 中心线 浮心 漂心 重心 冲子 中央控制室 中心处理平台 离心泵 离心机 防火陶棉 瓷砖

第三方检验机构

cellar shutdown panel (CSDP) 井口系统关断盘

倒链、链滑车 带扶手的半软椅 开坡口 槽钢

夏比V形缺口韧性值

charpy-V notch impact test chart datum check randomly check valve checkered plate chemical composition chemical injection package chemical injection system chemical seal chipping hammer Chisel Chord member Christmas tree circumference circumferential weld classification survey clean water injection pump clean water surge tank Clearance Client close drain tank closed / open circuit Closed drain pump 12

夏比V形缺口冲击试验 海图基准面 抽检 止回阀 花纹板 化学成分 化学注入撬 化学药剂注入系统 化学密封 敲渣锤 风铲 弦杆 采油树 周长 环焊缝 入级检验 清水注入泵 清水缓冲罐 间隙 业主、顾客 闭式排放罐 闭/开路 闭式排放泵

closed drain tank clustered well heads CO2 cylinder unit CO2 extinguisher coal tar epoxy paint Coaming Coating coating interval Coefficient Cold formed pipe cold shut cold work collapse ring Column

combustible gas detector Come-along

commercial blast cleaning commissioning

闭式排放罐 丛式井口 CO2 气瓶组 CO2 灭火器 含焦油环氧涂料 档水扁钢 涂装 涂漆间隔 系数 冷卷管 冷隔

冷加工、冷作 加强环板 立柱

可燃气体探测器 手搬葫芦 普通级喷砂除锈 调试

compile and maintain a document 编制和保存文件 complete penetration groove weld 全熔透坡口焊

Completion riser complex joint Compliance with comply with

13

完井立管 复杂节点 符合(名词) 符合(动词)

composite rockwool ceiling composite rockwool panel concentric reducer Conceptual design concrete platform Condensate drum Condensing water Conductor conductor guide Cone Connection consumption rate Continuous beam

Continuous double fillet weld Continuous welding Contract Contraction stress Contractor control valve

(accessories handwheel) control valve assembly coordinates coordination

14

复合岩棉天花板

复合岩棉板 同心大小头 概念设计 混凝土平台 冷凝液罐 冷凝水 隔水套管 套管导向 大小口、锥体 节点、连接 阳极消耗率 连续梁

双面连续贴角焊 连续焊 合同 收缩应力 承包商

带手轮的控制阀 控制阀总成 坐标系 协调

conform to = stick to = adhere to 符合、遵守

cope hole corrective and preventive action Correlation curve corrosion allowance corrosion coupon corrosion protection Corrugated plate interceptor Couplant Coupling Crack

crane barge, crane vessel crane support Crater crawler crane Criteria cross angle cross section crow bar cruciform bollard crude cooler crude filter

crude heat exchanger crude loading /export pump crude loading pump 15

(焊接)工艺孔 纠正和预防措施

相关曲线 腐蚀余量 腐蚀挂片 防腐 斜板分离器 UT用的耦合剂 连轴器 、管箍 裂纹 起重船 吊机支撑 焊口 履带吊车 (验收)标准 交叉角 横截面 撬杠

单十字带缆柱 原油冷却器 原油过滤器 原油换热器 原油外输泵 原油装载泵

百度搜索“77cn”或“免费范文网”即可找到本站免费阅读全部范文。收藏本站方便下次阅读，免费范文网，提供经典小说综合文库中海油员工英语手册(3)在线全文阅读。