77范文网 - 专业文章范例文档资料分享平台

AS 2537-1994 - 与使用冷热水的交联聚乙烯管(PE-X) 配合使用的机(5)

来源:网络收集 时间:2019-08-01 下载这篇文档 手机版
说明:文章内容仅供预览,部分内容可能不全,需要完整文档或者需要复制内容,请下载word后使用。下载word有问题请添加微信号:或QQ: 处理(尽可能给您提供完整文档),感谢您的支持与谅解。点击这里给我发消息

APPENDIX B

METHODS OF SPECIFYING SIZES AND TYPES OF FITTINGS

(Normative) 附录B

说明连接件尺寸和型号的方法

(规范性)

B1 SIZE SPECIFICATION B1 尺寸规范

Sizes of fittings shall be specified as outlined in Paragraph B1.1, B1.2 and B1.3. 连接件的尺寸应按照B1.1、B1.2 和B1.3的规定进行标注。 B1.1 Straight-through fittings B1.1 直通连接件

For fittings with two unequal ends, the larger end shall be given first. 对于两端不一样大的连接件,应先给出较大端。 B1.2 Fittings having three ends B1.2 具有三个末端的连接件

Fittings having three ends (?tees?) shall be specified first by the end of the ?run?, i.e. the two ends (the larger shall be specified first) in the same straight line, and then by the remaining end. (See Figure B1.)

对于具有三个末端(T型)的连接件,应先说明直通端,也就是处于一条直线上的两端(应先说明较大端),然后说明第三端。(见图B1) B1.3 Fittings have four ends B1.3 具有四个末端的连接件

Fittings having four ends (?crosses?) shall be specified first by the larger end on the ?run? and then by the second end on the ?run?, followed by the remaining ends, the larger of the two remaining ends being specified first. (See Figure B2.)

对于具有四个末端(交叉型)的连接件,应先说明直通的较大端,再说明直通的第二端,即下来说明剩余的两端,应先说明剩余两端的较大端。(见图B2)

(a) Tee 50×50×25 T型50×50×25

(b) Tee 50×40×25 T型50×40×25

(c) Tee 25×20×32 T型25×20×32

FIGURE B1 EXAMPLES SPECIFIYING SIZES OF FITTINGS HAVING THREE ENDS

图B1:具有三个末端的连接件尺寸说明示例

(a) Cross 32×25×20×20 (b) Cross

32×32×25×20

交叉型32×25×20×20 交叉型

32×32×25×20

(c) Cross 50×32×50×25 交叉型 50×32×50×25

FIGURE B2 EXAMPLES SPECIFYING SIZES OF FITTINGS HAVING FOUR ENDS

图B2:具有四个末端的连接件尺寸说明示例

B2 FASTENING B2 紧固 B2.1 General B2.1 总则

Fitting ends required to connect to existing plumbing systems shall comply with the appropriate Standard that applies to the connection.

连接件末端如需与现有管道工程连接,则必须符合适用于连接的相应标准要求。 B2.2 Fastening pipe threads B2.2 紧固管螺纹

Fastening pipe threads shall conform to the relevant requirements of AS 1722.2. 紧固管螺纹应满足AS 1722.2的相应要求。 B2.3 Sealing pipe threads B2.3 密封管螺纹

Sealing pipe threads shall conform to the relevant requirements of AS 1722.1. 密封管螺纹应满足AS 1722.1的相应要求。

APPENDIX C

METHOD FOR DETERMINING PRESSURE RESISTANCE OF FITTINGS

(Normative) 附录C

确定连接件耐压性的方法

(规范性)

C1 SCOPE C1 范围

This Appendix sets out a method for determining the pressure resistance of fittings intended for use with cross-linked polyethylene pipe.

本附录陈述了用于确定与交联聚乙烯管配合使用的连接件耐压性的方法。 C2 PRINCIPLE C2 原理

The joint assembly is subjected to a calculated test pressure equivalent to hoop stresses in the pipe of 4.8 MPa for a minimum period of 1 h and 4.2 MPa for a period of 3000 +100, ?0 h at 95 ±2°C. 让连接组件承受的测算压力相当于下列状况的管内环向压力:温度95 ±2°C,4.8 Mpa至少1小时或4.2 Mpa持续3000 +100, ?0小时。 C3 APPARATUS C3 设备

The following apparatus is required: 需要下列设备:

(a) Pressurizing system A hydraulic system capable of producing the required test pressure and capable of maintaining an accuracy of ±2%. A hydraulic accumulator or pump may be used for this purpose.

(a) 增压系统:能够产生所需测试压力并能保持精度为±2%的液压系统。为此可使用液压蓄力器或水泵。

Provision shall be made for one or more connections on the hydraulic system at the one time for connecting to joint assemblies. If a joint assembly bursts, means shall be provided to ensure that there will be no lowering of the pressure exceeding the ±2% tolerance allowable on other joint assemblies under test. Each connection shall be capable of being isolated.

应该为液压系统的一个或多个连接以及连接组件制定预防措施。如果一个连接组件爆裂,应该提供适当方式以确保测试中的其他连接组件的压力不得降低超过公差容许范围的±2%。每个连接都应相互独立。

(b) End connections Fittings shall be provided that will make a watertight connection at each end of the joint assembly. One fitting shall be connected to the hydraulic system, permitting the joint assembly to be suspended vertically. Fittings of the type illustrated in Figure C1 are considered suitable.

(b) 终端连接:应提供能在每个连接组件的端部做到水密性连接的连接件,应将一个连接件接到液压系统上,让连接组件能够垂直悬挂。图C1所示类型的连接件被认为是合适的。

(c) Reference pressure device A pressure gauge, or alternative equipment (e.g. pressure transducer) accurate to ±1% of the true value used for setting or measuring and recording the

百度搜索“77cn”或“免费范文网”即可找到本站免费阅读全部范文。收藏本站方便下次阅读,免费范文网,提供经典小说教育文库AS 2537-1994 - 与使用冷热水的交联聚乙烯管(PE-X) 配合使用的机(5)在线全文阅读。

AS 2537-1994 - 与使用冷热水的交联聚乙烯管(PE-X) 配合使用的机(5).doc 将本文的Word文档下载到电脑,方便复制、编辑、收藏和打印 下载失败或者文档不完整,请联系客服人员解决!
本文链接:https://www.77cn.com.cn/wenku/jiaoyu/667684.html(转载请注明文章来源)
Copyright © 2008-2022 免费范文网 版权所有
声明 :本网站尊重并保护知识产权,根据《信息网络传播权保护条例》,如果我们转载的作品侵犯了您的权利,请在一个月内通知我们,我们会及时删除。
客服QQ: 邮箱:tiandhx2@hotmail.com
苏ICP备16052595号-18
× 注册会员免费下载(下载后可以自由复制和排版)
注册会员下载
全站内容免费自由复制
注册会员下载
全站内容免费自由复制
注:下载文档有可能“只有目录或者内容不全”等情况,请下载之前注意辨别,如果您已付费且无法下载或内容有问题,请联系我们协助你处理。
微信: QQ: