77范文网 - 专业文章范例文档资料分享平台

AS 2537-1994 - 与使用冷热水的交联聚乙烯管(PE-X) 配合使用的机(2)

来源:网络收集 时间:2019-08-01 下载这篇文档 手机版
说明:文章内容仅供预览,部分内容可能不全,需要完整文档或者需要复制内容,请下载word后使用。下载word有问题请添加微信号:或QQ: 处理(尽可能给您提供完整文档),感谢您的支持与谅解。点击这里给我发消息

PREFACE 序言

This Standard was prepared by the Standards Australia Committee on Cross-linked Polyethylene (PE-X) Pipe to supersede AS 2537-1982. It applies to mechanical jointing fittings intended for use with PE-X pipe complying with AS 2492, Cross-linked polyethylene (PE-X) pipe for hot and cold water applications.

本标准由澳大利亚标准委员会针对交联聚乙烯管(PE-X)编制,用于代替AS2537-1982。本标准适用于与符合下列标准要求的PE-X管配合使用的机械连接件:AS 2492 使用冷热水的交联聚乙烯管(PE-X)。

This Standard incorporates Amendment No. 1 (December, 2002). The changes required by the Amendment are indicated in the text by a marginal bar and amendment number against the clause, note, table, figure or part thereof affected.

本标准配合使用修订本No.1的内容(2002年12月)。修订本有变更要求的正文中用边界竖线进行标示,对条款、注释、表格、图形或章节的修订号会对其产生影响。

The objective of this document is to provide a standard specification for use by manufacturers and purchasers of these products.

本标准的目的是向这些产品的制造商和产品购买者提供标准规范。

The terms ?normative? and ?informative? have been used in this Standard to define the application of the appendix to which they apply. A ?normative? appendix is an integral part of a Standard, whereas an ?informative? appendix is only for information and guidance.

本标准使用了术语“规范性”和“参考性”用于表明附件的适用情况,“规范性”附录表示该附录是本标准的一部分,而“参考性”附录仅作参考和指示性使用。

CONTENTS

目录

Page

页码

1 SCOPE………………………………………………………………………………………………5 1 范围

2 REFERENCED DOCUMENTS……………………………………………………………………5 2 参考文件

3 DEFINITIONS ………………………………………………………………………………………7 3 定义

4 CLASSIFICATION …………………………………………………………………………………7 4 分级

5 PRESSURE RATING ACCORDING TO TEMPERATURE ……………………………………7 5 根据温度而定的压力等级

6 SIZE AND TYPE ……………………………………………………………………………………7 6 尺寸和型号

7 COMPOSITION………………………………………………………………………………………8 7 成分

8 CONTAMINATION OF WATER……………………………………………………………………6 8 水污染

9 FREEDOM FROM DEFECTS………………………………………………………………………8 9 无缺陷

10 FASTENING ………………………………………………………………………………………10 10 紧固

11 PERFORMANCE REQUIREMENTS……………………………………………………………10 11 性能要求

12 MARKING …………………………………………………………………………………………12 12 标识

APPENDICES 附录

A MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD………………14 A 用于证明符合本标准的方式

B METHODS OF SPECIFYING SIZES AND TYPES OF FITTINGS …………………………17 B 说明连接件尺寸和型号的方法

C METHOD FOR DETERMINING PRESSURE RESISTANCE OF FITTINGS ………………20 C 确定连接件耐压性的方法

D ?Not applicable?……………………………………………………………………………………… D 不适用

E METHOD OF TEST FOR RESISTANCE TO LEAKAGE WHEN SUBJECTED TO

BENDING………………………………………………………………………………………………25 E 被弯曲时的抗渗漏性测试方法

F METHOD OF TEST FOR RESISTANCE TO PULL-OUT OF ASSEMBLED JOINTS………29 F 装配接头抗拉性的测试方法

G THERMAL CYCLING TEST……………………………………………………………………33 G 热循环测试

H METHOD OF TEST FOR LIQUID INFILTRATION……………………………………………35 H 液体渗透测试方法

I METHOD FOR DETERMINING PRESSURE RESISTANCE OF A JOINT…………………38 I 接头耐压性确定方法

STANDARDS AUSTRALIA

澳大利亚标准局 Australian Standard

Mechanical jointing fittings for use with cross-linked polyethylene (PE-X) pipe for hot and

cold water applications

澳大利亚标准

与使用冷热水的交联聚乙烯管(PE-X)配合使用的机械连接件

1 SCOPE 1 范围

This Standard specifies requirements for mechanical jointing fittings suitable for use as fixed joints, with cross-linked polyethylene (PE-X) pipes manufactured in accordance with AS 2492.

本标准对用作固定接头,与按照AS 2492标准制造的交联聚乙烯管(PE-X)配合使用的机械连接件规定了详细要求。 NOTES:

备注:

1 Joining cross-linked polyethylene pipe by means of solvent cement is not satisfactory. 以溶剂粘结剂与交联聚乙烯管连接的形式不符合要求。

2 Alternative means for demonstrating compliance with this Standard are given in Appendix A. 附录A给出了另一种符合本标准的示例形式。

2 REFERENCED DOCUMENTS 2 参考文件

The following documents are referred to in this Standard: 本标准参考了下列文件: AS 澳大利亚

1199 Sampling procedures and tables for inspection by attributes 1199 按属性检验的抽样程序和抽样表

1349 Bourdon tube pressure and vacuum gauges 1349 布尔登管压力计和真空计

1399 Guide to AS 1199—Sampling procedures and tables for inspection by attributes 1399 AS 1199指南——按属性检验的抽样程序和抽样表 1722 Pipe threads of Whitworth form 1722 惠氏螺纹牙样的管螺纹

1722.1 Part 1: Sealing pipe threads

1722.1 第1部分:密封管螺纹

1722.2 Part 2: Fastening pipe threads 1722.2 第二部分:紧固管螺纹

2345 Dezincification resistance of copper alloys 2345 铜合金抗脱锌性

2492 Cross-linked polyethylene (PE-X) pipe for hot and cold water applications 2492 使用冷热水的交联聚乙烯管(PE-X) 3500 National Plumbing and Drainage Code 3500 国家管道工程和排水规范 3500.0 Part 0: Glossary of Terms 3500.0 第0部分:术语表

3688 Water supply—Copper and copper alloy compression and capillary fittings and threaded

end connectors 3688 供水系统——铜和铜合金压缩、毛细连接配件和带螺纹的末端连接器 3707 Method for testing pressure cycling resistance of pipes and fittings 3707 管子及连接件的压力循环阻力测试方法

3855 Suitability of plumbing and water distribution system products for contact with potable

water 3855 管道工程和接触饮用水的水分配系统产品的适配性

4020 Products for use in contact with water intended for human consumption with regard to

their effect on the quality of water 4020* 用于接触人类消费用水从而需要考虑对水质影响的产品 AS/NZS

澳大利亚/新西兰标准

ISO 9000 Quality management and quality assurance standards ISO 9000 品质管理和品质保证标准

ISO 9000.1 Part 1: Guidelines to selection and use ISO 9000.1 第1部分:选择和使用的指导方针

ISO 9004 Quality management and quality system elements ISO 9004 品质管理和品质系统要素 ISO 9004.1 Part 1: Guidelines ISO 9004.1 第1部分:指导方针 SAA

澳大利亚标准协会

HB 18 Guidelines for third-party certification and accreditation HB 18 第三方认证和授权指导方针

*

* First published as an Interim Standard.

第一次发行时作为过渡性标准。

百度搜索“77cn”或“免费范文网”即可找到本站免费阅读全部范文。收藏本站方便下次阅读,免费范文网,提供经典小说教育文库AS 2537-1994 - 与使用冷热水的交联聚乙烯管(PE-X) 配合使用的机(2)在线全文阅读。

AS 2537-1994 - 与使用冷热水的交联聚乙烯管(PE-X) 配合使用的机(2).doc 将本文的Word文档下载到电脑,方便复制、编辑、收藏和打印 下载失败或者文档不完整,请联系客服人员解决!
本文链接:https://www.77cn.com.cn/wenku/jiaoyu/667684.html(转载请注明文章来源)
Copyright © 2008-2022 免费范文网 版权所有
声明 :本网站尊重并保护知识产权,根据《信息网络传播权保护条例》,如果我们转载的作品侵犯了您的权利,请在一个月内通知我们,我们会及时删除。
客服QQ: 邮箱:tiandhx2@hotmail.com
苏ICP备16052595号-18
× 注册会员免费下载(下载后可以自由复制和排版)
注册会员下载
全站内容免费自由复制
注册会员下载
全站内容免费自由复制
注:下载文档有可能“只有目录或者内容不全”等情况,请下载之前注意辨别,如果您已付费且无法下载或内容有问题,请联系我们协助你处理。
微信: QQ: