发动机反推显示丢失排故工卡(7)

A/C REG 机号 B-5488 Item 工序 REV. DATE TITLE 标题 LOSS OF THE THRUST REVERSER INDICIATION 修正日期 ON ENGINE 1 OR 2 2012-12-5 1号或2号发动机反推显示丢失 Job Description 工作单内容 CARD NO 卡号 AMM71-00-58 MECH INSP工作者 检查者 C. Access to the SYSTEM REPORT/TEST/INST page 进入系统REPORT/TEST/INST页面 (Ref. Fig. 208/TASK 31-32-00-991-008) ---------------------------------------------------------------------------------- ACTION 操作 RESULT结果 ----------------------------------------------------------------------------------1. Push the line key adjacent to the - the DMC1 (2 or 3) menu page EIS1 (2 or 3) indication comes into view 按下EIS1（2或3）附近的行选键 DMC1（2或3）菜单出现 2. Push the line key adjacent to the - the LRU IDENTIFICATION LRU IDENT indication page comes into view. 按下LRU显示附近的行选键 LRU代码页出现。 PAGE 页码 OF 2 A/C REG 机号 B-5488 Item 工序 REV. DATE TITLE 标题 LOSS OF THE THRUST REVERSER INDICIATION 修正日期 ON ENGINE 1 OR 2 2012-12-5 1号或2号发动机反推显示丢失 Job Description 工作单内容 CARD NO 卡号 AMM71-00-58 MECH INSP工作者 检查者 Make sure that the DMC - EIS SOFTWARE P/N shown on the LRU IDENTIFICATION page is the same as the computer P/N (given on the front face of the disks located in the disk stowage box). Make sure that the DMC - EIS SOFTWARE P/N shown on the LRU IDENTIFICATION page is the same as the other EIS components SOFTWARE P/N (the PFD CAPT, the ND CAPT, the EWD, the SD, the ND F/O, the PFD F/O, the other DMCs) 确定DMC-EIS软件在LRU代码页出现的键号和电脑键号（在磁盘表面给出了）一致。确定DMC-EIS软件在LRU代码页出现的键号和其他EIS组件软件键号（机长侧PFD、ND、EWD、SD，副驾驶侧ND、PFD，其他DMC）一致。 A. Close Access 关闭舱门 (1) Make sure that the work area is clean and clear of tool(s) and other items. 确保工作区域清洁，没有工具和其他物品。 (2) Close the access door 824. (Ref. TASK 52-41-00-410-002) 关闭824号舱门。 Subtask 52-41-00-410-056 D. Closing of the Avionics Compartment Door 824 (Access Door) 关闭电子仓824号舱门。 PAGE 页码 OF 2 A/C REG 机号 B-5488 Item 工序 REV. DATE TITLE 标题 LOSS OF THE THRUST REVERSER INDICIATION 修正日期 ON ENGINE 1 OR 2 2012-12-5 1号或2号发动机反推显示丢失 Job Description 工作单内容 CARD NO 卡号 AMM71-00-58 MECH INSP工作者 检查者 CAUTION：MAKE SURE THAT THE DOOR HANDLE IS FLUSH WITH THE DOOR RECESS BEFORE YOU MOVE IT INBOARD.THIS PREVENTS DAMAGE TO THE DOOR SKIN. 警戒：确保在你将门向内推时手柄和门上凹槽是平齐的。这能防止对门上蒙皮造成损伤。 CAUTION：WHEN YOU CLOSE THE AVIONICS COMPARTMENT DOOR, MAKE SURE THAT YOUR HANDS ARE NOT ON THE EDGE OF THE OPENING.THE DOOR CLOSES QUICKLY AT THE END OF THE MOVEMENT AND CAN CAUSE INJURY TO YOUR HANDS. 警戒：当关闭电子仓门时，确保你的手没有放在门口边缘。舱门在关闭的末尾速度很快，可能对手造成伤害。 (Ref. Fig. 205/TASK 52-41-00-991-006) (1) Pull on the door handle to move the access door down over its horizontal level. 用手拉着舱门手柄将它拉至水平位置。 NOTE : When the access door moves below the horizontal, the gas spring unit operates to lower the access door automatically. 提示：当舱门移动到水平位置以下时，气簧组件自动将门关闭。 (2) Make sure that your hands do not touch the door frame edge of the fuselage. 确保你的手没有接触机身的舱门框边缘。 PAGE 页码 OF 2 A/C REG 机号 B-5488 Item 工序 更换阻流门锁扣 REV. DATE TITLE 标题 LOSS OF THE THRUST REVERSER INDICIATION 修正日期 ON ENGINE 1 OR 2 2012-12-5 1号或2号发动机反推显示丢失 Job Description 工作单内容 CARD NO 卡号 AMM71-00-58 MECH INSP工作者 检查者 (2) Pull on the door handle to move the access door down into the door opening. 拉着舱门手柄将接近舱门拉入舱门开口。 Remove the access platform(s). 移除接近平台。 If the REV indication is not present on the upper ECAM display unit with the DMC3 switched on: 如果反推显示在DMC3打开的情况下还没有在ECAM的上显示器上出现： (1) Do a check to make sure that the blocker door latches are correctly unlocked. 检查确定阻流门锁扣正常解锁。 (a) If there are not correctly unlocked: 如果没有正常解锁： - replace the defective: LATCH-BLOCKER DOOR, UPPER R (3002KM1) or LATCH-BLOCKER DOOR, LOWER R (3002KM2) or LATCH-BLOCKER DOOR, UPPER L (3002KM3) or LATCH-BLOCKER DOOR, LOWER L (3002KM4) 更换故障锁钩：右上方阻流门锁扣（3002KM1）或者右下方阻流门锁扣（3002KM2）或者左上方阻流门锁扣（3002KM3）或者左下方阻流门锁扣（3002KM4）. (Ref. AMM TASK 78-31-19-000-001) and (Ref. AMM TASK 78-31-19-400-001). PAGE 页码 OF 2 A/C REG 机号 B-5488 Item 工序 REV. DATE TITLE 标题 LOSS OF THE THRUST REVERSER INDICIATION 修正日期 ON ENGINE 1 OR 2 2012-12-5 1号或2号发动机反推显示丢失 Job Description 工作单内容 CARD NO 卡号 AMM71-00-58 MECH INSP工作者 检查者 TASK 78-31-19-000-001 Removal of the Blocker Door Latches (3002KM1,3002KM2,3002KM3,3002KM4) 阻流门锁扣的拆除 1 . Reason for the Job 工作原因 锁扣损坏 2 . Job Set-up Information 工作准备 A. Fixtures, Tools, Test and Support Equipment 夹具，工具，测试和支持设备 ------------------------------------------------------- REFERENCE 参照 QTY DESIGNATION 数量 ------------------------------------------------------- No specific 没有要求 blanking plugs 遮蔽塞 No specific 没有要求 protective covers 保护罩 No specific 没有要求 warning notice 警示牌 No specific 没有要求 access platform 1 m (3 ft. 3 in.) 1m高接近平台（3英尺3英寸） HIX3005 1 SAFETY SLEEVE - PIVOTING DOOR ACTUATOR 旋转门作动筒安全套筒 PAGE 页码 OF 2

百度搜索“77cn”或“免费范文网”即可找到本站免费阅读全部范文。收藏本站方便下次阅读，免费范文网，提供经典小说综合文库发动机反推显示丢失排故工卡(7)在线全文阅读。