77范文网 - 专业文章范例文档资料分享平台

扩展电流反馈放大器的可用性(3)

来源:网络收集 时间:2021-09-24 下载这篇文档 手机版
说明:文章内容仅供预览,部分内容可能不全,需要完整文档或者需要复制内容,请下载word后使用。下载word有问题请添加微信号:或QQ: 处理(尽可能给您提供完整文档),感谢您的支持与谅解。点击这里给我发消息

Testing with ferrite chips used for Z

Ferrite chips have been available for severalyears, are relatively low-cost, and areavailable in verysmall sizes—0402 andlarger. Although several manufacturersproduce ferrite chips, testing was donewith what was availablein the test lab—ferrite chips from Murata’s BLM series.Examining the impedance characteristicsof these ferrites revealed several possiblecomponents that could be utilized.

The first factor in determining the propercomponent was the ferrite’s impedance atthe amplifier’s bandwidth limit. For theTHS3112, this implied an impedance of at least 600 at about 150 MHz to meetstability. This can vary, as the first testresults showed (see Figure 3).

Additionally, the Q of the ferrite chipsvaries from grade to grade. Some have alow Q with a fairly smooth rise to the resonance point that then subsides due toinherent properties and parasitics, whileother chips have a relatively high Q with asharp rise and fall in impedance associatedwith them. Although either style may

meet the impedance requirements, testingwas required to see if this Q had an effecton the circuit. Again, the best way to showthe results was to graph the frequencyresponse of the system, as shown inFigure 5. The responses below 10 MHzwere all identical to the original configu-ration. This figure concentrates on thestability portion of the responses above 10 MHz. For comparison purposes, the681- , pure-resistance response is shown.

晶闸管电源

Amplifiers: Op Amps

Texas Instruments Incorporated

Although all of these ferrite chips have

the same impedance at 100 MHz (600 ),they produced different results. The HDseries high-Q chip shows a very narrow

and large peak that will most likely result

in instability and oscillations. The AG andHG series low-Q chips both performed

about the same, and either one would

probably produce acceptable results. The

only difference is that the HG series has

impedance at higher frequencies andwould probably be better suited for usewith very high-speed CFB amplifiers suchas the OPA685 or the THS3202.

Notice that the pure resistance has a

lower response peak than the ferrite chips.

Coupled with the fact that the HD series

has a high Q and a high peak, this impliesthat the slope of the impedance at the

amplifier’s bandwidth is a factor for stabil-ity. This makes a lot of sense; as it is well

known that for any amplifier, if a zerointersects the amplifier’s open-loopresponse at a rate of closure of 40 dB/decade, large peaking and oscillations willmost likely result.5For this circuit config-uration, if the impedance of Z has a largeslope that intersects the transimpedancecurve at essentially a rate of closure of 40 dB/decade, peaking and oscillationsalso will most likely occur. By comparison,a resistor intersects the transimpedancecurve at a rate of closure of 20 dB/decade,resulting in a stable response. Even though

the low-Q ferrite beads have some slope

related to their impedance, the rate ofclosure is much lower than 40 dB/decade,

providing improved stability. Nevertheless,

minimizing this intersection rate of closureas much as possible should produceacceptable results.To further expand on the usefulness of

the ferrite chips, more testing was doneutilizing the AG series in the circuit,asshown in Figure 6.

This figure shows that, just like the

results for the pure resistor, the higher

the impedance is, the lower the peaking.

How does this affect the output noise ofthe system? Figure 7 shows the outputnoise when the ferrite chips were used,along with the output noise of the THS4012

and some of the original resistor configurations.Inverting gain configurationAs expected, due to the low frequency impedance of theAll of the testing discussed so far was done with the non-ferrite chips, the noise is extremely low. This noise was theinverting gain configuration. This configuration forces thesame regardless of which ferrite was used. If noise aboveinverting node voltage to move proportionally to the input10 MHz was important, the impedance of these ferritevoltage applied. So how does the system work in thechips would start to increase the output noise to the sameinverting gain configuration where the inverting node isextent as resistors. These tests show that there are severalheld at a virtual ground? The easy answer is that it worksadvantages of using ferrite chips over resistors.

晶闸管电源

Texas Instruments IncorporatedAmplifiers: Op Amps

exactly the same as before. Figures 8 and 9 show the testcircuits for this configuration. The signal gain was kept ata gain of 5.

The same concepts apply for this CFB configuration asfor the noninverting configuration. The advantage of thiscircuit is that the attenuation is not limited to unity gain,or 0 dB, like the noninverting gain circuit. Figure 10 showsthe frequency responses of this configuration with varyingpure resistor values for Z. The THS4012 response is shownfor comparison purposes.

百度搜索“77cn”或“免费范文网”即可找到本站免费阅读全部范文。收藏本站方便下次阅读,免费范文网,提供经典小说医药卫生扩展电流反馈放大器的可用性(3)在线全文阅读。

扩展电流反馈放大器的可用性(3).doc 将本文的Word文档下载到电脑,方便复制、编辑、收藏和打印 下载失败或者文档不完整,请联系客服人员解决!
本文链接:https://www.77cn.com.cn/wenku/yiyao/1255533.html(转载请注明文章来源)
Copyright © 2008-2022 免费范文网 版权所有
声明 :本网站尊重并保护知识产权,根据《信息网络传播权保护条例》,如果我们转载的作品侵犯了您的权利,请在一个月内通知我们,我们会及时删除。
客服QQ: 邮箱:tiandhx2@hotmail.com
苏ICP备16052595号-18
× 注册会员免费下载(下载后可以自由复制和排版)
注册会员下载
全站内容免费自由复制
注册会员下载
全站内容免费自由复制
注:下载文档有可能“只有目录或者内容不全”等情况,请下载之前注意辨别,如果您已付费且无法下载或内容有问题,请联系我们协助你处理。
微信: QQ: