77范文网 - 专业文章范例文档资料分享平台

2015《轮机英语》试题(二、三管轮)(10)

来源:网络收集 时间:2019-08-01 下载这篇文档 手机版
说明:文章内容仅供预览,部分内容可能不全,需要完整文档或者需要复制内容,请下载word后使用。下载word有问题请添加微信号:或QQ: 处理(尽可能给您提供完整文档),感谢您的支持与谅解。点击这里给我发消息

B. fuel injection pump √ C. crankshaft D. oil can

312.The _____ of the diesel oil must not exceed 120 degree Fahrenheit.

A. temperature √ B. pressure C. acid value D. viscosity

313.The _____ of the lubricant should be sufficient to hold the film together, but it should

allow the lubricant to flow easily. A. specific gravity B. viscosity √ C. acid value D. calorific value

314.The _____ chamber is enclosed between the cylinder head and piston.

A. lubrication B. injection C. cooling D. combustion √

315.The _____ or balance tank collects the re-circulated fuel oil.

A. buffer √ B. sump C. bilge D. overflowing

316.The _____ or balance tank collects the re-circulated fuel oil.

A. overflowing B. sump C. bilge D. buffer √

317.The _____ in the injector will lift at a pre-set pressure which ensures that the fuel

will atomize once it enters the cylinder. A. needle valve √ B. nozzles C. piston D. spring

318.The abbreviation BDC means _____.

A. Boston Diesel Company B. base circle diameter

C. switch board case D. bottom dead center √ 319.The abbreviation TDC means _____.

A. top dead center √

B. temperature difference center C. time delay dock D. top diesel company

320.The amount of lubricating oil in the drain tank should be checked by _____.

A. measuring B. sounding rod √ C. metering D. weighting

321.The auxiliary engine and a.cgenerator can be connected with _____.

A. cam B. crosshead C. bulge D. coupling √

322.The bearing shell generally has _____ for location and oil grooves round the center of

its axial length. A. tips B. tags √ C. lips D. keys

323.The bearing shells depend on the accuracy of _____ to held them in a truly circular shape.

A. the gap B. the clearance C. the bore √ D. the housing

324.The bed-plate is secured in the longitudinal direction by means of bolts known as _____.

A. end-chock bolts √ B. side-chock bolts C. through bolts D. tie rods

325.The bore of each cylinder is formed in a liner which can be _____ when worn out.

A. welded B. replaced √ C. drilled again D. bored

326.The burning of the fuel adds more heat to the air charge, causing it to expand and force

the engine piston to do work on the crankshaftWhat does “it” mean in this sentence? A. the burning B. the fuel

C. the air charge √ D. the engine piston

327.The cap and new shell are tightened up and then removed and the thickness of the wire

measured by _____. A. a bridge gauge B. a micrometer √ C. a thermometer D. a indicator

328.The carbon deposits on the piston crown and in the ring grooves _____.

A. should be scraped √ B. should be derusted C. should be drilled out D. to be brushed off

329.The cast iron _____ for the cross-head are attached to the top section and seal off the

crankcase.

A. cylinder cover B. cross-head shoes C. guide-ways √ D. scavenging boxes

330.The cast iron guide-ways for _____ are attached to the top section and seal off the

crankcase.

A. the connecting rod B. the cross-head √ C. the piston rod D. the air box

331.The cleaned heated oil, after passing through the centrifuges, is to be pumped to a _____.

A. settling tank B. service tank √ C. ballast tank D. drain tank

332.The common method of applying oil to the cylinder walls is by means of small pump assembled

in units, known as _____. A. mechanical lubricator √ B. lubrication function C. forced feed system D. bearing lubrication

333.The complete assembly of bedplate, A-frames and cylinder block is held together by _____

to form a rigid structure. A. tap-bolts B. jack-bolts C. tie rods √ D. fitted rods

334.The compressed air is admitted to each cylinder through a cam operated by starting air

valve when the piston has just passed its _____. A. BDC B. TDC √ C. BBDC D. ATDC

335.The compressed air is supplied by _____ to the air reservoirs.

A. compressors √ B. forced fans C. ventilators D. generators

336.The conclusion that mechanical efficiency is always _____ 100 per cent is correct.

A. small than B. more than C. little than D. less than √

337.The connecting rod large end bearing shell generally has tags for location and oil grooves

round the center of its axial length which correspond with grooves in the _____ through which oil is transmitted up the rod to lubricate the small end. A. connecting rod B. piston rod C. bearing housing √ D. none of the above

338.The cooler as the liquid becomes, _____.

A. the faster it will evaporate B. the slower it will condense C. the slower it will evaporate √ D. the faster it will flow

339.The cooling liquid used for the cylinder may be referred to as _____.

A. jacket water √ B. make-up water C. boiler water D. flushing water

340.The cooling of the piston is carried out by circulating _____ across the underside of

the crown and inside the ring belt or through specially shaped passages. A. sea water B. scavenging air C. lubricating oil √ D. fuel oil

341.The cooling water is in direct contact with the outer surface of the liner as a result

of which it is termed a _____. A. water liner B. wet liner √ C. dry liner D. drown liner

342.The cooling water jacket is common to all the cylinders but there are often _____ to

ensure that each cylinder receives the right amount and flow of water. A. dividing walls √ B. divided walls C. dividing liners D. divided jackets

343.The cooling water temperature _____ over a period of 8 hours, and then shut down.

A. should be gradually increased B. should be gradually reduced √ C. should be constantly kept D. should be varied up and down

344.The correct tightening is obtained by use of _____ to measure the extension given to

the bolts.

A. pressure gauges B. stretch gauges √ C. thermometers D. bridge gauges

345.The crank chamber oil _____.

A. can be recovered √

B. is only supplied to cylinders C. only feeds the main bearing D. is a kind of detergent

346.The crank pin journal is provided with large bores for _____.

A. lubrication B. cooling

C. balancing purpose √ D. ventilation

百度搜索“77cn”或“免费范文网”即可找到本站免费阅读全部范文。收藏本站方便下次阅读,免费范文网,提供经典小说教育文库2015《轮机英语》试题(二、三管轮)(10)在线全文阅读。

2015《轮机英语》试题(二、三管轮)(10).doc 将本文的Word文档下载到电脑,方便复制、编辑、收藏和打印 下载失败或者文档不完整,请联系客服人员解决!
本文链接:https://www.77cn.com.cn/wenku/jiaoyu/667961.html(转载请注明文章来源)
Copyright © 2008-2022 免费范文网 版权所有
声明 :本网站尊重并保护知识产权,根据《信息网络传播权保护条例》,如果我们转载的作品侵犯了您的权利,请在一个月内通知我们,我们会及时删除。
客服QQ: 邮箱:tiandhx2@hotmail.com
苏ICP备16052595号-18
× 注册会员免费下载(下载后可以自由复制和排版)
注册会员下载
全站内容免费自由复制
注册会员下载
全站内容免费自由复制
注:下载文档有可能“只有目录或者内容不全”等情况,请下载之前注意辨别,如果您已付费且无法下载或内容有问题,请联系我们协助你处理。
微信: QQ: